Single component — no mixing errors, minimal wastage
Coloured coating over acrylic polymer cementitious coatings (APCC)
Rayson UraForce HY15
Rayson UraForce HY15 is a single-component, water-based hybrid urethane — a self-crosslinking acrylic-copolymer-enhanced polyurethane — that roller-coats concrete and mineral surfaces with a fast-drying, stain-resistant, anti-slip finish.
Best for
Best for quick-turnaround coloured floor coating on walkways, playgrounds and commercial areas where single-pack simplicity and fast drying matter.
Real product · Interactive depth view Rayson UraForce
Product system Rayson UraForce HY15
24 kg plastic pail RY-TDS-705
Rayson UraForce HY15 has one clearly defined, verifiable job in the coating system.
Rayson UraForce HY15 is a single-component, water-based hybrid urethane — a self-crosslinking acrylic-copolymer-enhanced polyurethane — that roller-coats concrete and mineral surfaces with a fast-drying, stain-resistant, anti-slip finish. Best for quick-turnaround coloured floor coating on walkways, playgrounds and commercial areas where single-pack simplicity and fast drying matter.
Fast-drying: overcoat in 1–3 hours, light traffic in 4–6 hours at 25 °C
Grey concrete walkways and commercial floors
Stain-resistant, easy-to-clean, anti-slip finish
Hard surfaces such as stone and limestone
One pack. Fast drying. Back in service sooner.
A single-component hybrid urethane for stain-resistant, easy-clean and anti-slip floors in walkways and commercial areas.
A controlled route to applying Rayson UraForce HY15.
This sequence supports early planning. It does not replace the current Technical Data Sheet, approved method statement or project-specific technical review.
- 01
Inspect and prepare the substrate
Mineral substrates and grey concrete
- 02
Prepare the material as specified
Single component, ready to use; pot life stated as under 4 hours once opened and in use
- 03
Apply with the correct tools
Recommended methods: Brush, Roller. Confirm coat count and thickness for the project.
- 04
Protect through the required cure
Overcoat in 1–3 hours at 25 °C (substrate dependent); open to light traffic after 4–6 hours
Coating system cutaway
Every layer has a job—from prepared substrate to service surface.
This diagram explains a typical system position, not a fixed specification. Primer, body coat, finish, thickness and detailing must be confirmed for the project.
Position in the system Finish
Rayson UraForce HY15 serves as the finish. Confirm the complete build-up against the substrate, exposure and project requirements.
Related system products
Review primers, body layers, finishes or specialist components connected to this product.
- Rayson UraForce HY15Finish · Hybrid urethane
- Compatible body coat / baseProvides the required thickness and continuity beneath the finish
- Approved primer / baseIncluded when required by the system design
- Correctly prepared substrateMineral substrates and grey concrete
Four project facts for faster system screening.
These current product figures support early selection. Confirm the final build-up, quantity and application conditions against the Technical Data Sheet and site conditions.
- Coverage
- Coverage
- Mixing & working time
- Mixing
- Drying & curing
- Curing
- Pack configuration
- Pack
Refer to the Technical Data Sheet
Single component, ready to use; pot life stated as under 4 hours once opened and in use
Overcoat in 1–3 hours at 25 °C (substrate dependent); open to light traffic after 4–6 hours
24 kg plastic pail
Confirm the substrate and real service environment before specifying.
Choose it when
- Coloured coating over acrylic polymer cementitious coatings (APCC)
- Grey concrete walkways and commercial floors
- Hard surfaces such as stone and limestone
- Pavers, playgrounds and basketball courts
Relevant applications
Relevant industries
Choose something else when
- Ambient and surface temperatures must be at least 5 °C above the dew point
- Recommended wet film thickness approximately 130–150 microns per coat
- A thin-film finish, not a levelling or heavy-duty build product
- Shelf life shorter than two-pack products — rotate stock
- Heavy industrial or forklift traffic — use an epoxy or PU-cement system
- Chemical spill or containment areas
- Levelling uneven substrates — it is a thin roller coat
Other Rayson products to evaluate
These links continue the comparison; they are not automatic substitutes. Confirm the substrate, exposure and complete build-up before selection.
Substrate requirements+
- Mineral substrates and grey concrete
- Stone and limestone
- Pavers
- Acrylic polymer cementitious coatings
Technical documents and project support
Ready to specify Rayson UraForce HY15? Give Rayson the site conditions.
Send the area, substrate condition, expected traffic or exposure, required finish and programme. The technical team can help review the system build-up and estimated quantity.
What to know before specifying Rayson UraForce HY15.
Does UraForce HY15 need a hardener?
No — it is a single-component, self-crosslinking product. Stir well and apply; there is no mix ratio to get wrong.
How fast can an area reopen?
Indicatively, light foot traffic after 4–6 hours at 25 °C, with overcoating possible from 1–3 hours.
Is it slippery when wet?
The finish is formulated with anti-slip character, and for ramps or wet zones it pairs with GripSafe AP12 textured primer for a defined anti-slip profile.
Can it be used outdoors?
Yes — it is non-yellowing and suitable for interior or exterior use, including playgrounds, pavers and walkways.
How many coats are recommended?
A minimum of two, with dull patches receiving a further coat for a uniform finish.
Related products
Specialist GripSafe
Rayson GripSafe AP12
Purpose-built anti-slip system
Rayson GripSafe AP12 is a one-pack, self-crosslinking acrylic primer filler loaded with 0.5–1.5 mm silicate quartz aggregate that builds an anti-slip texture directly onto concrete and asphalt.
Finish UraForce
Rayson UraForce WB52
Water-based polyurethane finish
Rayson UraForce WB52 is a two-component, water-based aliphatic urethane floor topcoat — low-VOC, low-odour and UV-resistant — that can be combined with broadcast aggregate for an anti-slip finish.
Prime PrimeBond
Rayson PrimeBond W10
Single-pack · water-based
Rayson PrimeBond W10 is a one-component, water-based acrylic primer, sealer and bonding agent for smooth concrete and mineral substrates, applied ahead of Rayson UraForce water-based topcoats.
Finish CourtFlex
Rayson CourtFlex AC25
Outdoor acrylic court finish
Rayson CourtFlex AC25 is a single-component, water-based, self-crosslinking acrylic co-polymer coating for sports courts and decorative concrete and masonry surfaces, forming a stain-resistant, easy-to-clean film.