Question 1

How should an industrial floor coating be selected?

Accepted Answer

Start with the operating requirement: substrate condition, traffic, chemicals, temperature, hygiene, wet grip, cleaning method and the access window the operation can genuinely provide. Product selection follows those conditions and must be verified against the relevant Rayson technical data sheets.

Question 2

Can one coating system be used throughout an entire facility?

Accepted Answer

Not always. Production lines, wash-down bays, ramps, loading areas, chemical stores and public zones often face different traffic, temperature, cleaning and exposure. A dependable brief evaluates the facility zone by zone.

Question 3

Can Rayson recommend a coating from the available shutdown window?

Accepted Answer

The shutdown window is an important project constraint, but it is not enough on its own. Rayson also needs the substrate, area, current condition, operating exposure and cleaning method before shortlisting products and checking the published cure information in each TDS.

Question 4

Where can consultants and auditors find Rayson product data?

Accepted Answer

Rayson publishes its technical data sheets in the public TDS library. Each relevant product card on this page links directly to the product page and its TDS so intended use, application method, coverage, mixing, cure information and limitations can be reviewed.

Question 5

What information should be sent for an industry coating recommendation?

Accepted Answer

Send the industry, facility zones, substrate, approximate area, traffic type, chemicals or wash-down exposure, temperature, cleaning method, current floor condition and the access or shutdown window available. Surface photos and drawings improve the initial review.

Question 6

Does Rayson publish coating-floor maintenance guidance?

Accepted Answer

Yes. Industry guidance covers routine cleaning, inspection of high-traffic or high-risk zones and planned recoating before the substrate becomes exposed. This is general technical guidance and should be read with the relevant product TDS.

Question 7

How should ESD flooring be specified for electronics facilities?

Accepted Answer

ESD flooring should be considered together with the target resistance range, grounding layout, production traffic, cleaning method and verification plan. The public Rayson article and relevant StaticGuard product TDS provide the starting evidence for a technical review.

Question 8

How should slip resistance be discussed for wet industrial areas?

Accepted Answer

Specify the real wet-service condition, contamination, cleaning method and recognised test approach instead of relying only on the word anti-slip. Texture also has to balance grip, cleanability and wear over the operating life of the floor.

Question 9

What operating requirements should be reviewed for Aerospace Facilities?

Accepted Answer

Aerospace hangars and MRO facilities need seamless, hard-wearing floors that resist hydraulic fluids, take point loads from jacking and tooling, and stay easy to inspect and clean. Rayson supplies epoxy primer, self-levelling and coating systems suited to hangar and workshop floors. The project brief should also record large open floor plates with long trafficked routes and strict fod (foreign object debris) control expectations, together with the available shutdown or phased-access window.

Question 10

What operating requirements should be reviewed for Car Parks?

Accepted Answer

Car park decks need coatings that handle constant tyre traffic, hot-tyre pickup, ramp braking forces and, on exposed decks, rain and UV. Rayson car park systems combine epoxy or polyurethane deck coatings with anti-slip ramp finishes and clear demarcation. The project brief should also record continuous vehicle traffic with tight closure windows and wet tyres tracking water across decks, together with the available shutdown or phased-access window.

Question 11

What operating requirements should be reviewed for Chemical Processing?

Accepted Answer

Chemical processing floors face spills, splash zones, wash-downs and thermal cycling. Rayson supplies chemical-resistant epoxy and polyurethane-cement systems with coved details that protect concrete and keep bunds and process areas serviceable. The project brief should also record frequent wash-down and chemical dosing and forklift and drum traffic across process areas, together with the available shutdown or phased-access window.

Question 12

What operating requirements should be reviewed for Education?

Accepted Answer

Schools and campuses need safe, low-odour, easy-to-clean floors and walls that survive heavy foot traffic and frequent cleaning. Rayson water-based and hybrid systems are suited to occupied-building programmes and holiday work windows. The project brief should also record high pedestrian traffic with peak surges and occupied buildings sensitive to odour during works, together with the available shutdown or phased-access window.

Question 13

What operating requirements should be reviewed for Electronics?

Accepted Answer

Electronics manufacturing needs clean, dust-free, static-controlled floors. Rayson StaticGuard conductive systems and seamless epoxy floors support ESD-sensitive assembly, cleanrooms and component storage. The project brief should also record esd-protected areas with grounding requirements and controlled environments with air handling, together with the available shutdown or phased-access window.

Question 14

What operating requirements should be reviewed for Food & Beverage?

Accepted Answer

Food and beverage floors must survive hot wash-downs, fats and acids, and support hygiene audits. Rayson PurScreed polyurethane-cement and sealed epoxy systems provide seamless, cleanable floors for production, packing and cold-room areas. The project brief should also record daily wash-down regimes with hot water and chemicals and hygiene audits requiring seamless, cleanable surfaces, together with the available shutdown or phased-access window.

Question 15

What operating requirements should be reviewed for Manufacturing & Warehousing?

Accepted Answer

Factories and warehouses need floors that take forklift traffic, racking loads and abrasion while staying easy to clean and mark out. Rayson epoxy coating, self-levelling and screed systems keep production and logistics floors working. The project brief should also record mhe traffic around the clock in busy dcs and racking point loads and drag loads, together with the available shutdown or phased-access window.

Question 16

What operating requirements should be reviewed for Offices?

Accepted Answer

Office and commercial interiors need smart, durable, low-odour floor and wall finishes that install fast and stay presentable. Rayson water-based epoxy and hybrid urethane systems suit lobbies, corridors, back-of-house and plant rooms. The project brief should also record occupied buildings requiring low-odour products and after-hours and weekend work windows, together with the available shutdown or phased-access window.

Question 17

What operating requirements should be reviewed for Retail?

Accepted Answer

Retail floors must look good under continuous footfall, trolley traffic and daily cleaning — often with overnight-only installation windows. Rayson fast-recoat epoxy and urethane systems keep shopfloors open for business. The project brief should also record trading-hours restrictions — overnight work windows and continuous public foot traffic, together with the available shutdown or phased-access window.

Question 18

What operating requirements should be reviewed for Sports?

Accepted Answer

Sports courts and recreation surfaces need consistent traction, ball response and colour that lasts outdoors. Rayson CourtFlex acrylic systems coat courts, multi-purpose games areas and recreational surfaces. The project brief should also record outdoor uv and monsoon rain exposure and multi-sport usage with different traction needs, together with the available shutdown or phased-access window.

Every industry defines a good floor differently.

The coating is chosen around your calendar too.

Each zone needs its own isolation and handback plan.

The risk decides the system—not the product name.

Factory and warehouse floors matched to your forklift traffic

Food and beverage floors that survive the wash-down

Car park decks that grip when it rains — and stay watertight when it pours

ESD flooring you can actually measure

Floors specified against your actual chemical exposure

School floors that fit the holiday window

Office floors installed around the people still working

Retail floors finished overnight, open by morning

Hangar floors that shrug off hydraulic fluid

Sports surfaces that hold their colour and their grip

From how you operate to what goes on the floor.

Manufacturing & Warehousing

Rayson GripSafe AP12

Rayson PrimeBond E20

Rayson PrimeBond E25

Rayson PrimeBond S30

Rayson PrimeBond W10

Rayson FloorGuard R50

Rayson LevelShield SL120

Rayson MortarBond EM90

Rayson PurScreed PC70

Rayson CourtFlex AC25

Rayson StaticGuard CX90

Rayson UraForce HY15

Rayson UraForce SB65

Rayson UraForce SB72

Rayson UraForce WB52

Rayson UraForce WB58

Rayson UraForce WB60

Rayson HydroShield WE40

Rayson HydroShield WE45

Rayson PatchBond TX80

Rayson SealForce RC30

Rayson SealForce RC40

Rayson SealForce SP200

Rayson SealForce SP210

Your auditor can read our data sheets without asking us.

ESD and static control

Slip resistance in wet service

Chemical-plant flooring

Food-factory flooring

A good system has to survive ownership, not just handover.

Manufacturing & Warehousing

Food & Beverage

Car Parks

Electronics

Chemical Processing

Education

Offices

Retail

Aerospace Facilities

Sports

Questions facility teams ask before specification

We make it, so the answer comes from the formulation.

Tell us how the facility runs. We’ll work back to the system.