Retains colour and high gloss under strong UV
Exterior industrial floors
Rayson UraForce SB72
Rayson UraForce SB72 is a two-component, solvent-based polyurethane floor finish that holds its colour and high gloss under strong UV while resisting abrasion and a broad range of chemicals.
Best for
Best for exterior industrial floors and any coated floor where colour and gloss must survive sunlight.
Real product · Interactive depth view Rayson UraForce
Product system Rayson UraForce SB72
Part A 4.5 kg can + Part B 1 kg can RY-TDS-701
Rayson UraForce SB72 has one clearly defined, verifiable job in the coating system.
Rayson UraForce SB72 is a two-component, solvent-based polyurethane floor finish that holds its colour and high gloss under strong UV while resisting abrasion and a broad range of chemicals. Best for exterior industrial floors and any coated floor where colour and gloss must survive sunlight.
Excellent abrasion resistance (90 mg, CS-17 Taber)
Floors requiring long-term colour and gloss retention
Documented resistance to a wide schedule of acids, alkalis and fuels
Chemically exposed floors needing an easy-to-clean coloured finish
Keep the colour. Keep the gloss.
A UV-stable polyurethane finish that protects exterior industrial floors against sunlight, abrasion and chemical exposure.
A controlled route to applying Rayson UraForce SB72.
This sequence supports early planning. It does not replace the current Technical Data Sheet, approved method statement or project-specific technical review.
- 01
Inspect and prepare the substrate
Primed concrete (minimum 28 days cure, moisture content below 4%, laitance-free)
- 02
Prepare the material as specified
Mix ratio 3:1 (A:B) by weight; add all of Part B to the Part A container and mix with an electric mixer until homogeneous; do not dilute with thinner; pot life 8 hours at 25 °C
- 03
Apply with the correct tools
Recommended methods: Fine smooth lamb wool roller. Confirm coat count and thickness for the project.
- 04
Protect through the required cure
Foot traffic 8 h at 25 °C; vehicular traffic 48 h; full chemical resistance 7 days. Recoat window 8–48 hours at 25 °C
Coating system cutaway
Every layer has a job—from prepared substrate to service surface.
This diagram explains a typical system position, not a fixed specification. Primer, body coat, finish, thickness and detailing must be confirmed for the project.
Position in the system Finish
Rayson UraForce SB72 serves as the finish. Confirm the complete build-up against the substrate, exposure and project requirements.
Related system products
Review primers, body layers, finishes or specialist components connected to this product.
- Rayson UraForce SB72Finish · Polyurethane
- Compatible body coat / baseProvides the required thickness and continuity beneath the finish
- Approved primer / baseIncluded when required by the system design
- Correctly prepared substratePrimed concrete (minimum 28 days cure, moisture content below 4%, laitance-free)
Four project facts for faster system screening.
These current product figures support early selection. Confirm the final build-up, quantity and application conditions against the Technical Data Sheet and site conditions.
- Coverage
- Coverage
- Mixing & working time
- Mixing
- Drying & curing
- Curing
- Pack configuration
- Pack
Material consumption 0.10 L/m² per coat
Mix ratio 3:1 (A:B) by weight; add all of Part B to the Part A container and mix with an electric mixer until homogeneous; do not dilute with thinner; pot life 8 hours at 25 °C
Foot traffic 8 h at 25 °C; vehicular traffic 48 h; full chemical resistance 7 days. Recoat window 8–48 hours at 25 °C
Part A 4.5 kg can + Part B 1 kg can
Confirm the substrate and real service environment before specifying.
Choose it when
- Exterior industrial floors
- Floors requiring long-term colour and gloss retention
- Chemically exposed floors needing an easy-to-clean coloured finish
Relevant applications
Concrete Floors Car Park Decks Roofs & Exposed Structures Warehouses & Manufacturing Areas Chemical-Processing Environments
Relevant industries
Choose something else when
- Do not dilute with thinner
- In cold weather, allow a longer cure before applying the second coat
- Solvent-based — provide adequate ventilation; not for occupied areas without ventilation control
- Requires a fully cured, efficiently sealing primer coat — surface defects telegraph through thin finishes
- Occupied or unventilated areas during application — solvent-based
- Unprimed or poorly sealed concrete
- Thick-build or self-levelling duties — this is a thin-film finish
- Immersion service or chemical exposures outside the tested schedule without technical confirmation
Other Rayson products to evaluate
These links continue the comparison; they are not automatic substitutes. Confirm the substrate, exposure and complete build-up before selection.
Substrate requirements+
- Primed concrete (minimum 28 days cure, moisture content below 4%, laitance-free)
- The primer coat must be fully cured and must seal the concrete efficiently before finishing
Technical documents and project support
Ready to specify Rayson UraForce SB72? Give Rayson the site conditions.
Send the area, substrate condition, expected traffic or exposure, required finish and programme. The technical team can help review the system build-up and estimated quantity.
What to know before specifying Rayson UraForce SB72.
Will UraForce SB72 yellow outdoors?
No — the aliphatic polyurethane chemistry is specifically chosen for colour and gloss retention under strong UV. That is its core advantage over epoxy finishes.
Which chemicals has it been tested against?
The source resistance schedule covers citric, tartaric, acetic, lactic and phosphoric acids, nitric acid 25%, hydrochloric acid 10%, sulphuric acid 30%, sodium hydroxide 30%, petrol, sugar solution and formaldehyde 38%. For any exposure outside that schedule, or unusual concentration and temperature, confirm with our technical team.
How long between the two coats?
Apply the second coat within roughly 8–48 hours at 25 °C; cold weather stretches the required cure before recoating.
When can vehicles drive on it?
Indicatively 48 hours at 25 °C, with full chemical resistance developing over 7 days. Programme heavy or chemical service accordingly.
Can it be applied without a primer?
No. Efficient sealing of the concrete by a cured primer coat is essential — an unsealed slab causes bubbles and defects in the thin finish film.
Is it suitable for occupied buildings?
Only with proper ventilation — it is solvent-based. For odour-sensitive interiors choose the water-based UraForce WB52, WB58 or WB60.
Related products
Prime PrimeBond
Rayson PrimeBond S30
Two-part · 2 × 10 L kit
Rayson PrimeBond S30 is a two-part, low-viscosity, solvent-based epoxy primer that penetrates and seals prepared concrete, pavements and mineral substrates before coating.
Prime PrimeBond
Rayson PrimeBond E20
Solvent-free · damp tolerant
Rayson PrimeBond E20 is a two-component, medium-viscosity, solvent-free epoxy bonding primer that anchors resin floor systems to concrete, screed, asphalt and prepared metal — on dry or damp substrates.
Finish UraForce
Rayson UraForce SB65
Two-part · 4 L + 1 L
Rayson UraForce SB65 is a two-component, solvent-based aliphatic polyurethane clear topcoat with excellent abrasion resistance, non-yellowing behaviour and outstanding weather durability for concrete, metal and stone.
Body LevelShield
Rayson LevelShield SL120
Self-smoothing · solvent-free
Rayson LevelShield SL120 is a solvent-free, two-component, self-smoothing epoxy floor system that delivers a seamless wearing surface with medium to heavy chemical resistance and high mechanical strength.